[Subject Prev][Subject Next][Thread Prev][Thread Next][Subject Index][Thread Index]

[vine-users:09988] Re: liloの設 定


こんばんわ

マザーボードAX6BC TYPE-R (BIOS v2.35)に違うチップメーカーの128MBの
メモリーモジュールを3枚入れて、384MBとして、ちゃんとメモリ認識されてます。

取り合えず、参考になるかどうかは判りませんがdmesg出力とlilo.confを
書き出しておきます。

Linux version 2.2.10 (root@kurasawa.linux.net) (gcc version 2.7.2.3) #2 SMP Wed Jul 21 22:57:22 JST 1999
mapped APIC to ffffe000 (0022c000)
mapped IOAPIC to ffffd000 (0022d000)
Detected 451028088 Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 448.92 BogoMIPS
Memory: 387524k/393216k available (884k kernel code, 416k reserved, 4128k data, 52k init)
Pentium-III serial number disabled.
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35 (19990512) Richard Gooch (rgooch@atnf.csiro.au)
Pentium-III serial number disabled.
per-CPU timeslice cutoff: 100.00 usecs.
CPU0: Intel 00/07 stepping 02
SMP motherboard not detected. Using dummy APIC emulation.
PCI: PCI BIOS revision 2.10 entry at 0xfb420
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
Starting kswapd v 1.5 
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
RAM disk driver initialized:  16 RAM disks of 4096K size
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
hda: ST38420A, ATA DISK drive
hdb: CD-ROM 40X/AKU, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ST38420A, 8223MB w/512kB Cache, CHS=1048/255/63, UDMA
hdb: ATAPI 40X CD-ROM drive, 128kB Cache
Uniform CDROM driver Revision: 2.55
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
scsi : 0 hosts.
scsi : detected total.
Partition check:
 hda: hda1 hda2 < hda5 >
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
(scsi0) <Adaptec AHA-2940A Ultra SCSI host adapter> found at PCI 11/0
(scsi0) Narrow Channel, SCSI ID=7, 3/255 SCBs
(scsi0) Downloading sequencer code... 413 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.17/3.2.4
       <Adaptec AHA-2940A Ultra SCSI host adapter>
scsi : 1 host.
(scsi0:0:6:0) Synchronous at 10.0 Mbyte/sec, offset 8.
  Vendor: MATSHITA  Model: CD-R   CW-7502    Rev: 4.17
  Type:   CD-ROM                             ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0
sr0: scsi3-mmc drive: 8x/8x writer xa/form2 cdda tray
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 52k freed
Adding Swap: 128484k swap-space (priority -1)
es1370: version v0.22 time 23:01:01 Jul 21 1999
es1370: found adapter at io 0x9400 irq 11
es1370: features: joystick off, line in, mic impedance 0
tulip.c:v0.91 4/14/99 becker@cesdis.gsfc.nasa.gov
eth0: Digital DS21143 Tulip rev 48 at 0x9800, 00:C0:CA:11:1C:47, IRQ 10.
eth0:  EEPROM default media type Autosense.
eth0:  Index #0 - Media 10baseT (#0) described by a 21142 Serial PHY (2) block.
eth0:  Index #1 - Media 10baseT-FD (#4) described by a 21142 Serial PHY (2) block.
eth0:  Index #2 - Media 100baseTx (#3) described by a 21143 SYM PHY (4) block.
eth0:  Index #3 - Media 100baseTx-FD (#5) described by a 21143 SYM PHY (4) block.
VFS: Disk change detected on device ide0(3,64)

boot=/dev/hda
map=/boot/map
install=/boot/boot.b
prompt
timeout=50
image=/boot/vmlinuz-2.2.10
        label=linux
        root=/dev/hda1
        initrd=/boot/initrd-2.2.10.img
        read-only
image=/boot/vmlinuz.old
        label=old
        root=/dev/hda1
        initrd=/boot/initrd-2.2.10.img

---
倉沢 佳樹

この情報があなたの探していたものかどうか選択してください。
yes/まさにこれだ!   no/違うなぁ   part/一部見つかった   try/これで試してみる

あなたが探していた情報はどのようなことか、ご自由に記入下さい。特に「まさにこれだ!」と言う場合は記入をお願いします。
例:「複数のマシンからCATV経由でipmasqueradeを利用してWebを参照したい場合の設定について」