[Subject Prev][Subject Next][Thread Prev][Thread Next][Subject Index][Thread Index]

[vine-users:020061] Re: Vine 2.0 beta2 X problem


おはようございます。中村@仙台です。

Yasuhide OOMORI / 大森保英 さんwrote:
> Vine-2.0beta についての質問は、どちらかといえば tester ML の方がいいか
> もしれません…。
vine tester MLは、どこにあるのでしょうか?
(すいません。検索で「tester」で引いたのですが見つからなかったのです。)

それから、ビデオチップは、savage mx(8MB)です。
3.3.6のリリースノートをみると、savage系での最後のサポートとなる様子で
一応使えるみたいだったのですが。うーん。
PCは、エプソンダイレクトのNT-1000です。

以下、startx &> x.logのログと、/etc/X11/XF86Configを載せます。
長くなってしまってすいません。

---------------------------------------------------------

XFree86 Version 3.3.6 / X Window System
(protocol Version 11, revision 0, vendor release 6300)
Release Date: January 8 1999
	If the server is older than 6-12 months, or if your card is newer
	than the above date, look for a newer version before reporting
	problems.  (see http://www.XFree86.Org/FAQ)
Operating System: Linux 2.2.14-1k3smp i686 [ELF] 
Configured drivers:
  SVGA: server for SVGA graphics adaptors (Patchlevel 0):
      NV1, STG2000, RIVA 128, RIVA TNT, RIVA TNT2, RIVA ULTRA TNT2,
      RIVA VANTA, RIVA ULTRA VANTA, RIVA INTEGRATED, GeForce 256,
      GeForce DDR, Quadro, ET4000, ET4000W32, ET4000W32i, ET4000W32i_rev_b,
      ET4000W32i_rev_c, ET4000W32p, ET4000W32p_rev_a, ET4000W32p_rev_b,
      ET4000W32p_rev_c, ET4000W32p_rev_d, ET6000, ET6100, et3000, pvga1,
      wd90c00, wd90c10, wd90c30, wd90c24, wd90c31, wd90c33, gvga, r128, ati,
      sis86c201, sis86c202, sis86c205, sis86c215, sis86c225, sis5597,
      sis5598, sis6326, sis530, sis620, sis300, sis630, sis540, tvga8200lx,
      tvga8800cs, tvga8900b, tvga8900c, tvga8900cl, tvga8900d, tvga9000,
      tvga9000i, tvga9100b, tvga9200cxr, tgui9400cxi, tgui9420, tgui9420dgi,
      tgui9430dgi, tgui9440agi, cyber9320, tgui9660, tgui9680, tgui9682,
      tgui9685, cyber9382, cyber9385, cyber9388, cyber9397, cyber9520,
      cyber9525, 3dimage975, 3dimage985, cyber9397dvd, blade3d, cyberblade,
      clgd5420, clgd5422, clgd5424, clgd5426, clgd5428, clgd5429, clgd5430,
      clgd5434, clgd5436, clgd5446, clgd5480, clgd5462, clgd5464, clgd5465,
      clgd6205, clgd6215, clgd6225, clgd6235, clgd7541, clgd7542, clgd7543,
      clgd7548, clgd7555, clgd7556, ncr77c22, ncr77c22e, cpq_avga, mga2064w,
      mga1064sg, mga2164w, mga2164w AGP, mgag200, mgag100, mgag400, oti067,
      oti077, oti087, oti037c, al2101, ali2228, ali2301, ali2302, ali2308,
      ali2401, cl6410, cl6412, cl6420, cl6440, video7, ark1000vl, ark1000pv,
      ark2000pv, ark2000mt, mx, realtek, s3_savage, s3_virge, AP6422, AT24,
      AT3D, s3_svga, NM2070, NM2090, NM2093, NM2097, NM2160, NM2200,
      ct65520, ct65525, ct65530, ct65535, ct65540, ct65545, ct65546,
      ct65548, ct65550, ct65554, ct65555, ct68554, ct69000, ct64200,
      ct64300, mediagx, V1000, V2100, V2200, p9100, spc8110, i740, i740_pci,
      Voodoo Banshee, Voodoo3, smi, generic
(using VT number 7)

XF86Config: /usr/X11R6/lib/X11/XF86Config
(**) stands for supplied, (--) stands for probed/default values
(**) XKB: disabled
(**) XKB: keymap: "xfree86(us)" (overrides other XKB settings)
(**) Mouse: type: PS/2, device: /dev/mouse, buttons: 3
(**) Mouse: 3 button emulation (timeout: 50ms)
(**) SVGA: Graphics device ID: "Generic VGA"
(**) SVGA: Monitor ID: "LCD 1024x768"
(--) SVGA: Mode "1024x768" needs vert refresh rate of 45.21 Hz. Deleted.
(**) FontPath set to
"/usr/X11R6/lib/X11/fonts/misc/,/usr/X11R6/lib/X11/fonts/75dpi/:unscaled,/usr/X11R6/lib/X11/fonts/100dpi/:unscaled,/usr/X11R6/lib/X11/fonts/Type1/,/usr/X11R6/lib/X11/fonts/Speedo/,/usr/X11R6/lib/X11/fonts/75dpi/,/usr/X11R6/lib/X11/fonts/100dpi/"
(--) SVGA: PCI: S3 Unknown chipset (0x8c10) rev 17, Memory @ 0xf0000000
RENDITION: vendor 0x8086 chip 0x7190
RENDITION: vendor 0x8086 chip 0x7191
RENDITION: vendor 0x12eb chip 0x3
RENDITION: vendor 0x8086 chip 0x7110
RENDITION: vendor 0x8086 chip 0x7111
RENDITION: vendor 0x8086 chip 0x7112
RENDITION: vendor 0x8086 chip 0x7113
RENDITION: vendor 0x10ec chip 0x8139
RENDITION: vendor 0x1180 chip 0x476
RENDITION: vendor 0x1180 chip 0x476
RENDITION: vendor 0x5333 chip 0x8c10
SVGA: 's3_savage' is an invalid chipset
 *** None of the configured devices were detected.***


Fatal server error:
no screens found

When reporting a problem related to a server crash, please send
the full server output, not just the last messages

X connection to :0.0 broken (explicit kill or server shutdown).
----------------------------------------------------------
x.log ここまで。

以下 XF86Config
----------------------------------------------------------
# File generated by xf86config.

#
# Copyright (c) 1995 by The XFree86 Project, Inc.
#
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions:
# 
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
# 
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
# THE XFREE86 PROJECT BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
# OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
# SOFTWARE.
# 
# Except as contained in this notice, the name of the XFree86 Project shall
# not be used in advertising or otherwise to promote the sale, use or other
# dealings in this Software without prior written authorization from the
# XFree86 Project.
#

# **********************************************************************
# Refer to the XF86Config(4/5) man page for details about the format of 
# this file.
# **********************************************************************

# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.

    RgbPath	"/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
# 
# If you don't have a floating point coprocessor and emacs, Mosaic or other
# programs take long to start up, try moving the Type1 and Speedo directory
# to the end of this list (or comment them out).
# 

#    FontPath   "/usr/X11R6/lib/X11/fonts/local/"
    FontPath   "/usr/X11R6/lib/X11/fonts/misc/"
    FontPath   "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
    FontPath   "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
    FontPath   "/usr/X11R6/lib/X11/fonts/Type1/"
    FontPath   "/usr/X11R6/lib/X11/fonts/Speedo/"
    FontPath   "/usr/X11R6/lib/X11/fonts/75dpi/"
    FontPath   "/usr/X11R6/lib/X11/fonts/100dpi/"

# For OSs that support Dynamically loaded modules, ModulePath can be
# used to set a search path for the modules.  This is currently supported
# for Linux ELF, FreeBSD 2.x and NetBSD 1.x.  The default path is shown
# here.

#    ModulePath "/usr/X11R6/lib/modules"

EndSection

# **********************************************************************
# Module section -- this is an optional section which is used to specify
# which dynamically loadable modules to load.  Dynamically loadable
# modules are currently supported only for Linux ELF, FreeBSD 2.x
# and NetBSD 1.x.  Currently, dynamically loadable modules are used
# only for some extended input (XInput) device drivers.
# **********************************************************************
#
# Section "Module"
#
# This loads the module for the Joystick driver
#
# Load "xf86Jstk.so"
# 
# EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is 
# received.  This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

#    NoTrapSignals

# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.

#    DontZap

# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences.  This allows clients to receive these key events.

#    DontZoom

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.

#       DisableVidModeExtension

# Uncomment this to enable the use of a non-local xvidtune client. 

#       AllowNonLocalXvidtune

# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings. 

#       DisableModInDev

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).

#       AllowNonLocalModInDev

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Keyboard section
# **********************************************************************

Section "Keyboard"

    Protocol	"Standard"

# when using XQUEUE, comment out the above line, and uncomment the
# following line

#    Protocol	"Xqueue"

    AutoRepeat	500 30
# Let the server do the NumLock processing.  This should only be required
# when using pre-R6 clients
#    ServerNumLock

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
#    Xleds      1 2 3

# To set the LeftAlt to Meta, RightAlt key to ModeShift, 
# RightCtl key to Compose, and ScrollLock key to ModeLock:

    LeftAlt     Meta
    RightAlt    ModeShift
#    RightCtl    Compose
#    ScrollLock  ModeLock

# To disable the XKEYBOARD extension, uncomment XkbDisable.

    XkbDisable

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults).  For example, for a non-U.S.
# keyboard, you will probably want to use:
#    XkbModel    "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
#    XkbModel    "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#    XkbLayout   "de"
# or:
#    XkbLayout   "de"
#    XkbVariant  "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
#    XkbOptions  "ctrl:swapcaps"

# These are the default XKB settings for XFree86
#    XkbRules    "xfree86"
#    XkbModel    "pc101"
#    XkbLayout   "us"
#    XkbVariant  ""
#    XkbOptions  ""

    XkbKeymap   "xfree86(us)"


EndSection


# **********************************************************************
# Pointer section
# **********************************************************************

Section "Pointer"
    Protocol    "PS/2"
    Device      "/dev/mouse"

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

#    Protocol	"Xqueue"

# Baudrate and SampleRate are only for some Logitech mice
# or for the AceCad tablets which require 9600 baud

#    BaudRate	9600
#    SampleRate	150

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

    Emulate3Buttons
    Emulate3Timeout    50

# ChordMiddle is an option for some 3-button Logitech mice

#    ChordMiddle

EndSection


# **********************************************************************
# Xinput section -- this is optional and is required only if you
# are using extended input devices.  This is for example only.  Refer
# to the XF86Config man page for a description of the options.
# **********************************************************************
#
# Section "Xinput" 
#    SubSection "WacomStylus"
#        Port "/dev/ttyS1"
#        DeviceName "Wacom"
#    EndSubSection
#    SubSection "WacomCursor"
#        Port "/dev/ttyS1"
#    EndSubSection
#    SubSection "WacomEraser"
#        Port "/dev/ttyS1"
#    EndSubSection
#
#    SubSection "Elographics"
#        Port "/dev/ttyS1"
#        DeviceName "Elo"
#        MinimumXPosition 300
#        MaximumXPosition 3500
#        MinimumYPosition 300
#        MaximumYPosition 3500
#        Screen 0
#        UntouchDelay 10
#        ReportDelay 10
#    EndSubSection
#
#    SubSection "Joystick"
#        Port "/dev/joy0"
#        DeviceName "Joystick"
#        TimeOut 10
#        MinimumXPosition 100
#        MaximumXPosition 1300
#        MinimumYPosition 100
#        MaximumYPosition 1100
#        # CenterX 700
#        # CenterY 600
#        Delta 20
#    EndSubSection
#
# The Mouse Subsection contains the same type of entries as the
# standard Pointer Section (see above), with the addition of the
# DeviceName entry.
#
#    SubSection "Mouse" 
#        Port "/dev/mouse2"
#        DeviceName "Second Mouse"
#        Protocol "Logitech"
#    EndSubSection
# EndSection

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

    Identifier  "LCD 1024x768"
    VendorName  "Unknown"
    ModelName   "Unknown"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    HorizSync   30-100

#    HorizSync	30-64         # multisync
#    HorizSync	31.5, 35.2    # multiple fixed sync frequencies
#    HorizSync	15-25, 30-50  # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    VertRefresh 50-100

# Modes can be specified in two formats.  A compact one-line format, or
# a multi-line format.

# These two are equivalent

#    ModeLine "1024x768i" 45 1024 1048 1208 1264 768 776 784 817 Interlace

#    Mode "1024x768i"
#        DotClock	45
#        HTimings	1024 1048 1208 1264
#        VTimings	768 776 784 817
#        Flags		"Interlace"
#    EndMode

# This is a set of standard mode timings. Modes that are out of monitor spec
# are automatically deleted by the server (provided the HorizSync and
# VertRefresh lines are correct), so there's no immediate need to
# delete mode timings (unless particular mode timings don't work on your
# monitor). With these modes, the best standard mode that your monitor
# and video card can support for a given resolution is automatically
# used.

# 640x400 @ 70 Hz, 31.5 kHz hsync
Modeline "640x400"     25.175 640  664  760  800   400  409  411  450
# 640x480 @ 60 Hz, 31.5 kHz hsync
Modeline "640x480"     25.175 640  664  760  800   480  491  493  525
# 800x600 @ 56 Hz, 35.15 kHz hsync
ModeLine "800x600"     36     800  824  896 1024   600  601  603  625
# 1024x768 @ 87 Hz interlaced, 35.5 kHz hsync
Modeline "1024x768"    44.9  1024 1048 1208 1264   768  776  784  817 Interlace

# 1024x768 @ 100.2 Hz, 40 kHz hsync
Modeline "1024x768"    50.6  1024  1032 1152 1360  768  784  787  823

# 640x400 @ 85 Hz, 37.86 kHz hsync
Modeline "640x400"     31.5   640  672 736   832   400  401  404  445 -HSync +VSync
# 640x480 @ 72 Hz, 36.5 kHz hsync
Modeline "640x480"     31.5   640  680  720  864   480  488  491  521
# 640x480 @ 75 Hz, 37.50 kHz hsync
ModeLine  "640x480"    31.5   640  656  720  840   480  481  484  500 -HSync -VSync
# 800x600 @ 60 Hz, 37.8 kHz hsync
Modeline "800x600"     40     800  840  968 1056   600  601  605  628 +hsync +vsync

# 640x480 @ 85 Hz, 43.27 kHz hsync
Modeline "640x480"     36     640  696  752  832   480  481  484  509 -HSync -VSync

# 800x600 @ 72 Hz, 48.0 kHz hsync
Modeline "800x600"     50     800  856  976 1040   600  637  643  666 +hsync +vsync
# 1024x768 @ 60 Hz, 48.4 kHz hsync
Modeline "1024x768"    65    1024 1032 1176 1344   768  771  777  806 -hsync -vsync

# 640x480 @ 100 Hz, 53.01 kHz hsync
Modeline "640x480"     45.8   640  672  768  864   480  488  494  530 -HSync -VSync
# 800x600 @ 85 Hz, 55.84 kHz hsync
Modeline  "800x600"    60.75  800  864  928 1088   600  616  621  657 -HSync -VSync

# 1024x768 @ 70 Hz, 56.5 kHz hsync
Modeline "1024x768"    75    1024 1048 1184 1328   768  771  777  806 -hsync -vsync

# 800x600 @ 100 Hz, 64.02 kHz hsync
Modeline  "800x600"    69.65  800  864  928 1088   600  604  610  640 -HSync -VSync
# 1024x768 @ 76 Hz, 62.5 kHz hsync
Modeline "1024x768"    85    1024 1032 1152 1360   768  784  787  823

# 1024x768 @ 85 Hz, 70.24 kHz hsync
Modeline "1024x768"   98.9  1024 1056 1216 1408   768 782 788 822 -HSync -VSync

# 1024x768 @ 100Hz, 80.21 kHz hsync
Modeline "1024x768"   115.5  1024 1056 1248 1440  768  771  781  802 -HSync -VSync
Modeline "1024x768"   115.5  1024 1056 1248 1440  768  771  781  802 

# 512x384 @ 78 Hz, 31.50 kHz hsync
Modeline "512x384"    20.160 512  528  592  640   384  385  388  404 -HSync -VSync
# 512x384 @ 85 Hz, 34.38 kHz hsync
Modeline "512x384"    22     512  528  592  640   384  385  388  404 -HSync -VSync

# Low-res Doublescan modes
# If your chipset does not support doublescan, you get a 'squashed'
# resolution like 320x400.

# 320x200 @ 70 Hz, 31.5 kHz hsync, 8:5 aspect ratio
Modeline "320x200"     12.588 320  336  384  400   200  204  205  225 Doublescan
# 320x240 @ 60 Hz, 31.5 kHz hsync, 4:3 aspect ratio
Modeline "320x240"     12.588 320  336  384  400   240  245  246  262 Doublescan
# 320x240 @ 72 Hz, 36.5 kHz hsync
Modeline "320x240"     15.750 320  336  384  400   240  244  246  262 Doublescan
# 400x300 @ 56 Hz, 35.2 kHz hsync, 4:3 aspect ratio
ModeLine "400x300"     18     400  416  448  512   300  301  302  312 Doublescan
# 400x300 @ 60 Hz, 37.8 kHz hsync
Modeline "400x300"     20     400  416  480  528   300  301  303  314 Doublescan
# 400x300 @ 72 Hz, 48.0 kHz hsync
Modeline "400x300"     25     400  424  488  520   300  319  322  333 Doublescan
# 480x300 @ 56 Hz, 35.2 kHz hsync, 8:5 aspect ratio
ModeLine "480x300"     21.656 480  496  536  616   300  301  302  312 Doublescan
# 480x300 @ 60 Hz, 37.8 kHz hsync
Modeline "480x300"     23.890 480  496  576  632   300  301  303  314 Doublescan
# 480x300 @ 63 Hz, 39.6 kHz hsync
Modeline "480x300"     25     480  496  576  632   300  301  303  314 Doublescan
# 480x300 @ 72 Hz, 48.0 kHz hsync
Modeline "480x300"     29.952 480  504  584  624   300  319  322  333 Doublescan

EndSection


# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
    Identifier	"Generic VGA"
    VendorName	"Unknown"
    BoardName	"Unknown"

    Chipset	"s3_savage"

    VideoRam	8192
#    Clocks	25.2 28.3

EndSection

# Sample Device for accelerated server:

# Section "Device"
#    Identifier	"Actix GE32+ 2MB"
#    VendorName	"Actix"
#    BoardName	"GE32+"
#    Ramdac	"ATT20C490"
#    Dacspeed	110
#    Option	"dac_8_bit"
#    Clocks	 25.0  28.0  40.0   0.0  50.0  77.0  36.0  45.0
#    Clocks	130.0 120.0  80.0  31.0 110.0  65.0  75.0  94.0
# EndSection

# Sample Device for Hercules mono card:

# Section "Device"
#    Identifier "Hercules mono"
# EndSection

# Device configured by xf86config:

Section "Device"
    Identifier  "My Video Card"
    VendorName  "S3"
    BoardName   "savage mx"
    VideoRam    8192
    Chipset     "s3_savage"
#    Clocks      130.0 120.0 80.0 50.4 31.0 110.0 65.0 75.0 94.0
#    Ramdac      "stg1703"
#    Clockchip   "s3_sdac"
EndSection


# **********************************************************************
# Screen sections
# **********************************************************************

# The Colour SVGA server

Section "Screen"
    Driver      "svga"
    Device      "Generic VGA"
    #Device      "My Video Card"
    Monitor     "LCD 1024x768"
    Subsection "Display"
        Depth       8
        #Modes       "640x480" "800x600" "1024x768" "1280x1024"
        ViewPort    0 0
        Virtual     320 200
        #Virtual     1600 1280
    EndSubsection
EndSection

# The 16-color VGA server

Section "Screen"
    Driver      "vga16"
    Device      "Generic VGA"
    Monitor     "LCD 1024x768"
    Subsection "Display"
   #     Modes       "640x480" "800x600"
        Modes       "800x600" "640x480"
        ViewPort    0 0
        Virtual     800 600
    EndSubsection
EndSection

# The Mono server

Section "Screen"
    Driver      "vga2"
    Device      "Generic VGA"
    Monitor     "LCD 1024x768"
    Subsection "Display"
        Modes       "640x480" "800x600"
        ViewPort    0 0
        Virtual     800 600
    EndSubsection
EndSection

# The accelerated servers (S3, Mach32, Mach8, 8514, P9000, AGX, W32, Mach64)

Section "Screen"
    Driver      "accel"
    Device      "My Video Card"
    Monitor     "LCD 1024x768"
    Subsection "Display"
        Depth       8
        Modes       "640x480" "800x600" "1024x768" "1280x1024"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       16
        Modes       "640x480" "800x600" "1024x768" "1280x1024"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       24
        Modes       "640x480" "800x600" "1024x768" "1280x1024"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       32
        Modes       "640x480" "800x600" "1024x768"
        ViewPort    0 0
    EndSubsection
EndSection

---------------------------------------------------------
XF86Configの方は、ほとんどいじってないので、そのままといった感じです。
(ドキュメント読んだのですが、
何で数値を見つけたらよいのやらといったところです。)
現在までは、chipsetの項目をいじって、genericでもだめだったところまで
確認できてます。
聞いてばかりで申し訳ありません。
では。

-- 
中村 崇志
東北大学理学研究科気象学講座
ntakashi@wind.geophys.tohoku.ac.jp

この情報があなたの探していたものかどうか選択してください。
yes/まさにこれだ!   no/違うなぁ   part/一部見つかった   try/これで試してみる

あなたが探していた情報はどのようなことか、ご自由に記入下さい。特に「まさにこれだ!」と言う場合は記入をお願いします。
例:「複数のマシンからCATV経由でipmasqueradeを利用してWebを参照したい場合の設定について」
Follow-Ups: References: